Product SKUs

MBD-PDSM4+-O
PDSM4+ (Standard Retail Pack)
MBD-PDSM4+-B
PDSM4+ (Bulk Pack)

Physical Stats

Form Factor
ATX
Dimensions
12" x 9.6", (30.5cm x 24.4 cm)

Processor/Cache

CPU
Single LGA775 ZIF Socket
Supports a Quad-Core Intel® Xeon® 3200 series processor
Supports a Dual-Core Intel® Xeon® 3000 series processor
Supports a Quad-Core Intel® Core™2 Extreme series processor
Supports an Intel® Core™2 Quad series processor
Supports an Intel® Core™2 Duo series processor
Supports an Intel® Pentium® processor E2000 series
Supports a Dual-Core Intel® Pentium® D processor
Supports an Intel® Pentium® Extreme Edition processor
Supports an Intel® Pentium® 4 processor
Supports an Intel® Celeron® processor E1000 series
Supports an Intel® Celeron® processor 400 series
NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
System Bus
1066 / 800 / 533 MHz system bus

System Memory

Memory Capacity
Four 240-pin DIMM sockets
Supports up to 8 GB of memory (Single / Dual Channel)
Memory Type
DDR2 667/533MHz unbuffered, ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
DIMM Sizes
256 MB, 512 MB, 1 GB, 2GB
Memory Voltage
1.8V only

On-Board Devices

Chipset
Intel 3010 (Mukilteo-2P) chipset
ICH7R + PXH + Intel® 82573V + Intel® 82573L
Serial ATA
Intel® ICH7R SATA2 (3 Gbps) controller built-in
Intel:
RAID 0, 1, 5, 10 support (Windows Only)
Adaptec:
RAID 0 (Two, three, four drives only)
RAID 1 (Two hard drives only)
SCSI
Adaptec AIC-7901 Single-channel U320 SCSI Controller
HostRAID 0, 1, 10 Supported
SCSI ZCR
Support for Zero-Channel RAID
Optional: (Card NOT included)
IPMI
Support for Intelligent Platform Management Interface v.2.0
IPMI 2.0 with virtual media over LAN & optional KVM-over-LAN support
Supermicro Intelligement Management
(Optional: AOC-SIM1U+)
NOTE: Must use dedicated LAN for IPMI function
Network Controllers
2x Single-port Gigabit PCI-Express Ethernet Controllers
Intel® 82573V
Supports 10BASE-T, 100BASE-T, 1000BASE-T, RJ45 output
VGA
On-board ATI ES1000 (16MB) graphics
Super I/O
Winbond W83627HG chip
Clock Generator
CK410

Input / Output

Serial ATA
Four Serial ATA ports (3 Gbps performance)
Four SATA hard drives supported
IDE
One EIDE channel supports up to two UDMA IDE devices
Supports UDMA Mode 5, PIO Mode 4, and ATA/100
Floppy
1 Floppy controller; 1.44 MB
LAN
2x RJ45 LAN ports
USB
Up to 4x USB 2.0 / 1.1 compliant ports
2 rear ports
1 internal header for 2 USB 2.0/1.1 ports
VGA
1x VGA port
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Ports
1x Fast UART 16550 serial port
1x internal header

Chassis ( Optimized for PDSM4+ )

2U
CSE-823S-R500LP
CSE-823S-550LP
Tower / 4U Rackmount
CSE-742S-420
Important Note
For a general system, a 420W (minimum) ATX12V power supply [8-pin +12V AND 24-pin is recommended to assure system stability].

Expansion Slots

PCI-Express
1 (x8) PCI-e slot
1 (x4) PCI-e slot
PCI-X
2x 64-bit 133MHz PCI-X (3.3V) slots
2x 64-bit 100MHz PCI-X (3.3V) slots

System BIOS

BIOS Type
8Mb Flash EEPROM with Phoenix BIOS®
BIOS Features
Plug and Play (PnP)
DMI 2.3 support
PCI 2.2
ACPI 1.0
SMBIOS 2.3
USB Keyboard support

Management

Software
Optional IPMI (Intelligent Platform Management Interface) 2.0
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Keyboard Wakeup from Soft-Off
CPU Fan auto-off in sleep mode
Power-on mode control for AC power loss recovery
Internal/External modem remote ring-on

PC Health Monitoring

Voltage
Monitors for CPU Cores (+1.5V, +1.8V, +3.3V, +5, ±12V, +5V Standby, VBAT)
CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.3750V-1.6000V
FAN
Total of six 4-pin fan headers
6x fans with tachometer monitoring
Status monitor with firmware / software speed control
Status monitor for on/off control
Support 3-pin fans (with speed control)
Low noise fan speed control
Pulse Width Modulated (PWM) fan connector
Temperature
Monitoring for CPU and chassis environment
CPU Thermal Trip support
Thermal Monitor (TM2) Support
LED
CPU / System Overheat LED
Standby alert LED
Suspend-state indicator LED
Other Features
Chassis intrusion detection
Chassis intrusion header

Operating Environment

Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)

OS Compatibility

• Please see our OS Compatibility Chart

Regulatory

FCC
Passed to meet FCC standard requirement

További specifikáció